Quant 3D Q150 Guide de l'utilisateur Page 118
- Page / 122
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
CAUTION! Cleaning and Decontamination. Use only the cleaning and
decontamination methods specified in the manufacturer's user documentation.
It is the responsibility of the operator (or other responsible person) to ensure
the following requirements are met:
·
No decontamination or cleaning agents are used that could cause a
HAZARD as a result of a reaction with parts of the equipment or with
material contained in the equipment.
·
The instrument is properly decontaminated a) if hazardous material is
spilled onto or into the equipment, and/or b) prior to having the instrument
serviced at your facility or sending the instrument for repair, maintenance,
trade-in, disposal, or termination of a loan (decontamination forms may be
requested from customer service).
·
Before using any cleaning or decontamination methods (except those
recommended by the manufacturer), users should confirm with the
manufacturer that the proposed method will not damage the equipment.
Safety and electromagnetic compatibility (EMC) standards
The instrument design and manufacture complies with the standards and
requirements for safety and electromagnetic compatibility as noted in the following
table:
Reference
Description
EU Directive
2006/95/EC
European Union “Low Voltage Directive”
CSA C22.2 No.
61010-1
IEC 61010-1
UL 61010-1
IEC/CSA/UL 61010-1
Safety requirements for electrical equipment for measurement,
control, and laboratory use – Part 1: General requirements
IEC 61010-2-010
[1]
Safety requirements for electrical equipment for measurement,
control, and laboratory use – Part 2-010: Particular requirements
for laboratory equipment for the heating of materials
[1]
A
pplies only to the QuantStudio
®
3D Digital PCR Chip Loader.
Reference
Description
Directive 2004/108/EC European Union “EMC Directive”
EN 61326-1
Electrical Equipment for Measurement,
Control and Laboratory Use – EMC
Requirements – Part 1: General
Requirements
FCC Part 18 (47 CFR) U.S. Standard “Industrial, Scientific, and
Medical Equipment”
Cleaning and
decontamination
Safety
EMC
Appendix E Safety
Safety and electromagnetic compatibility (EMC) standards
E
118
QuantStudio
®
3D Digital PCR System User Guide
- QuantStudio 1
- 3D Digital PCR System 1
- Contents 3
- (Optional) 5
- About this guide 8
- Prerequisites 9
- Instrument hardware 9
- Instrument software 9
- Instrument consumables 10
- Getting Started 11
- Data collection 12
- Instrument filters 12
- Operating the instrument 13
- Prepare the QuantStudio 14
- Plan the 15
- Choose additional 16
- Install the 17
- Digital PCR 17
- Instrument 17
- IMPORTANT! The QuantStudio 20
- The QuantStudio 21
- Install the thermal 23
- IMPORTANT! The ProFlex 24
- PCR System 26
- CAUTION HOT 27
- Install the GeneAmp 29
- PCR System 9700 29
- IMPORTANT! The GeneAmp 30
- IMPORTANT! If the GeneAmp 31
- Connect the QuantStudio 34
- 3D Instrument to a network 34
- 3D AnalysisSuite 35
- Software 35
- Prepare Samples and Load 36
- Reactions 36
- Sample dilution 37
- Determine the 37
- Prepare the 39
- X0300036 41
- Load and seal the 43
- IMPORTANT! Press the 45
- Load chips manually 50
- Digital PCR 20K 51
- IMPORTANT! Allow the 53
- Perform the PCR 58
- 08:00 AM 4/25/13 25.0°C 60
- GeneAmp® PCR System 9700 60
- Run UserUtilEditCreate 60
- Version: 3.12 60
- Materials 61
- Guidelines for 62
- Unload the 64
- Analyze the Prepared Chips 66
- Analysis workflow 67
- About the 68
- Analyze the chips 69
- Analyzing the data 73
- About the results 74
- About data quality 75
- About the data 75
- Transfer the 76
- Using the QuantStudio 77
- Troubleshooting 79
- (QuantStudio 82
- IMPORTANT! Condensation 83
- Maintenance 86
- Clean the chip tray 87
- Returning your QuantStudio 89
- 3D Instrument for service 89
- Replace the instrument fuses 90
- Replace the fuses 91
- Update the 92
- Calibrate the touchscreen 93
- View the instrument log 93
- Networking 95
- Network setup 96
- Required network 97
- Connect the 98
- Instrument to a 98
- Create a network 103
- Parts and Materials 106
- Specifications and Layout 109
- Instrument clearances 110
- Electrical specifications 111
- Environmental requirements 112
- Network requirements 113
- Symbols on this instrument 114
- Conformity 115
- Location of safety 116
- Fisher Scientific 117
- Instrument safety 117
- 3D Digital PCR Chip Loader 118
- Chemical safety 119
- Biological hazard safety 120
- Documentation and support 121
- 4 February 2015 122
© 2020, manymanuals.fr. Tous droits réservés | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels